110 lines
3.7 KiB
Makefile
110 lines
3.7 KiB
Makefile
|
|
|
|
# project specific files
|
|
SRC = matrix.c
|
|
|
|
# MCU name
|
|
MCU = atmega32u4
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU = 16000000
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in *bytes*
|
|
# Teensy halfKay 512
|
|
# Teensy++ halfKay 1024
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
# USBaspLoader 2048
|
|
#OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
# as per original hasu settings
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
|
COMMAND_ENABLE = yes # Commands for debug and configuration
|
|
CUSTOM_MATRIX = yes # Custom matrix file for the HHKB
|
|
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
|
# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
|
|
# NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
|
# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
|
|
# MIDI_ENABLE = yes # MIDI controls
|
|
# UNICODE_ENABLE = yes # Unicode
|
|
# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
|
|
|
|
|
|
# HHKB_RN42_ENABLE = yes # Enable support for hasu's BT alt controller -- code borrowed from tmk source tree.
|
|
|
|
# Either uncomment the HHKB_RN42_ENABLE line above, or run make enabling the
|
|
# feature. Be sure to clean any existing build before trying to enable rn42
|
|
# support. For example:
|
|
#
|
|
# make hhkb-keymap-clean
|
|
# make hhkb-keymap-dfu HHKB_RN42_ENABLE=yes
|
|
|
|
ifeq ($(strip $(HHKB_RN42_ENABLE)), yes)
|
|
|
|
OPT_DEFS += -DHHKB_RN42_ENABLE
|
|
|
|
# Support for the RN42 Bluetooth module. This is the BT module in Hasu's BT
|
|
# HHKB Alt controller.
|
|
RN42_DIR = rn42
|
|
|
|
SRC += serial_uart.c \
|
|
rn42/suart.S \
|
|
rn42/rn42.c \
|
|
rn42/rn42_task.c \
|
|
rn42/battery.c \
|
|
rn42/main.c
|
|
|
|
VPATH += $(RN42_DIR)
|
|
|
|
endif
|
|
|
|
|
|
# debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
|
|
# debug-on: all
|
|
|
|
# debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
|
|
# debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
|
|
# debug-off: all
|